Sandblasting machine 200 liter | with cyclone and abrasive vacuum cleaner

Pressure sandblaster 200 l type “PREMIUM” with cyclone cleaner and abrasive suction device for the treatment of abrasive

Free blasting system for manual sandblasting for many different types of workpieces using a blasting machine with abrasive preparation. After blasting, the abrasive is collected by hand and pushed into the collecting funnel on the floor. The abrasive suction device sucks the abrasive out of the funnel and pulls it through the cyclone cleaner. The dust is extracted and collected in the vacuum cleaner's dust container. Coarse parts are separated out through a sieve.

The cleaned blasting media falls back into the vented pressure blasting tank and is available for reuse. All machine elements outside receive a single primer and topcoat. This is a very economical and effective solution for blasting work with semi-automatic abrasive recycling.

• fastest switch-off and switch-on times, whereby the regulations of the employers' liability insurance association are observed. (VBG 48)
  

• The pressure setting can be precisely adjusted before the actual sandblasting process, from 0.1 - 12.0 bar, continuously adjustable.

• Lower consumption of sandblasting media, as the pressure vessel remains permanently under pressure, so there is no unnecessary run-on of blasting media.

• When restarting, the full sandblasting pressure is immediately available at the nozzle and does not have to be built up slowly, which means significantly lower consumption of blasting media and significantly less wear on the sandblasting hose.

• No moisture build-up (condensate) in the container, as the boiler remains constantly under pressure and is not vented and vented at every start and stop. This procedure also gives rise to other advantages as follows:

• Optimal sandblasting media dosing with hardened fine dosing valve, lower compressed air requirement, thus a significant reduction in fuel consumption (diesel).

• A one-man operation, as the sandblasting pressure is constantly displayed by the tank pressure and can easily be changed on the manometer without having to start.

• No malfunction-prone device components such as control valves, diaphragms and seals, making it easy to maintain and reliable. All you have to do is check the blasting hose in the safety shutdown and, if necessary, replace it (control from outside possible at any time!).

1 pc. SAPI Premium precision blasting device 200 l
1 1/4 ”piping can be precisely regulated from 0.1 - 12 bar, TÜV-tested with a certificate,
Equipment:

• Fixed piping inside and outside 1 "
• Rubber-coated metal cone with rubber seal
• Generous manhole
• landing gear
• Abrasive dosing valve (suitable for all abrasives)
• Pressure control valve with manometer

1 pc including safety quick stop shutdown
With the SAPI safety quick stop shutdown, blasting becomes safe and economical. When you let go of the
Control lever, the pneumatic squeeze shut-off ensures that the flow of blasting media is stopped without the
To vent the boiler.

1 pc high-performance water separator 1 1/4 "
maintenance-free, permanently attached to the device.
9911.035

1 pc 10 m long-term blasting hose ø 25x7 mm
completely assembled with nozzle holder, back pressure lever, control line and blasting hose coupling
9856.128

1 pc boron carbide nozzle for blasting hose Ø 25x7 10 mm, long nozzle

1 pc funnel 500 x 500 x 380 mm
with approx. 4 m connection hose to the cyclone cleaner. The funnel is placed on the floor and the abrasive is pushed into the feed funnel by hand.

1 pc of abrasive vacuum cleaner
for transporting the abrasive into the cyclone cleaner and for collecting the dust particles.

After sandblasting, the vacuum cleaner sucks the abrasive out of the feed hopper and pulls it through the cyclone cleaner. Dust is separated out and collected in the dust container. Including 2 m connection hose to the cyclone cleaner.

1 pc cyclone cleaner with lifting device
as an attachment to the 200 l pressure blasting device for cleaning the blasting media. Incl. A lifting device for the mechanical lifting of the cyclone by approx. 200 mm for cleaning purposes and hose
Connections to the filling funnel and abrasive suction device. The cyclone can be locked in the raised position.
The abrasive is cleaned in the cyclone via an adjustable cascade. Dust particles are collected in the blasting abrasive vacuum cleaner, coarse particles are separated out via a sieve and the abrasive falls into the pressure blasting device for reuse.